Uninterruptible Power Supply EVO DSP TM 10-30kVA User’s manual
User’s manual 8 UPS EVO DSP TM 2.5.1 Internal Battery Connection The models EVO DSP TM 10-30 KVA can be equipped with internal batteries. In such
UPS EVO DSP TM 9 User’s manual 2.5.2 Power Connections The power screw terminals are located on the lower front side of the UPS. Refer to the names
User’s manual 10 UPS EVO DSP TM 2.5.2.3 Separated Bypass Mains Input Connection (Optional) Bring the circuit breaker on the distribution panel to
UPS EVO DSP TM 11 User’s manual 3 Operating Modes There are three operating modes, which differ in the path of the energy flow. UPS block diagrams
User’s manual 12 UPS EVO DSP TM When UPS has no separate Bypass mains input, Bypass line is also fed from the mains input. Thus, if such a device is
UPS EVO DSP TM 13 User’s manual 3.2 Normal Mode Energy is drawn from the mains input. Loads are fed via the Rectifier and the Inverter. The AC vol
User’s manual 14 UPS EVO DSP TM 4 Control and Monitoring 4.1 Front Panel The front panel located on the upper part of the UPS informs the user abo
UPS EVO DSP TM 15 User’s manual 4.1.2 Mimic Panel Mimic panel is a diagram, which shows the path of energy flow in the UPS by means of several LED’
User’s manual 16 UPS EVO DSP TM 4.1.3 Liquid Crystal Display (LCD) and User Menu LCD provides detailed information about device status, alarms and
UPS EVO DSP TM 17 User’s manual “ALARMS” TABLE CODE NAME DEFINITION A01 BYP BADSHAPE Bypass mains voltage is different than the Inverter reference
User’s manual 18 UPS EVO DSP TM “MEASUREMENTS” MENU MEASUREMENT DEFINITION LD = XXX % Ratio of the actual Inverter active power to its nominal valu
UPS EVO DSP TM 19 User’s manual “CONFIGURATION” MENU DATE = "dd-mm-yyyy" Shows system date in dd-mm-yyyy format (dd = day, mm = month, y
User’s manual 20 UPS EVO DSP TM 5 Operating Procedures This chapter defines the operating procedures to be followed to activate, deactivate and man
UPS EVO DSP TM 21 User’s manual 5.3 Switching into Manual Bypass during Operation Manual Bypass enables the user to isolate the electronic circuit
User’s manual 22 UPS EVO DSP TM 6 Operating Procedures for Parallel System 6.1 Introduction EVO DSP TM UPS are designed according to high MTBF f
UPS EVO DSP TM 23 User’s manual Figure - Communication cables connections between Parallel UPSs Do not remove the communication cables betw
User’s manual 24 UPS EVO DSP TM In case this communication cable is removed or damaged during parallel operation and the communication is lost, then
UPS EVO DSP TM 25 User’s manual 9 After completing the configuration of the name of each UPS and N value, switch on the Input circuit breaker (F1)
User’s manual 26 UPS EVO DSP TM 7 Features and Operating Limits 7.1 Mains Limits for Normal mode Frequency and RMS value of the mains input volta
UPS EVO DSP TM 27 User’s manual 7.4 Overload Behavior While operating in Normal or Battery mode, the UPS can feed overloads for a limited duration
UPS EVO DSP TM 1 User’s manual Important Notice Thank you for purchasing TECNOWARE UPS. This document provides instructions about safety, installa
User’s manual 28 UPS EVO DSP TM 8 Communication Interfaces All related terminals are on the Communication Interface board (A1). Connector layout is
UPS EVO DSP TM 29 User’s manual 8.3 Digital Inputs (UPS OFF and GEN ON) Voltage to be applied to the digital inputs is 5 VDC. Maximum current draw
User’s manual 30 UPS EVO DSP TM 9 Maintenance Batteries, fans and capacitors shall be replaced at the end of their lives. Hazardous voltage and h
UPS EVO DSP TM 31 User’s manual 10 Troubleshooting This section gives information about the procedures which shall be performed in case of abnormal
User’s manual 32 UPS EVO DSP TM Alarm Possible Cause Action to solve The UPS may not start up yet. This alarm is permanent if the UPS is intende
UPS EVO DSP TM 33 User’s manual Alarm Possible Cause Action to solve VDC NOT OK Any of the DC bus voltages approaches its lower/upper limits. May
User’s manual 34 UPS EVO DSP TM 11 Technical Specifications EVO DSP TM MODELS Rating [kVA] 10 15 20 30 ENVIRONMENTAL Storage temperature range -
UPS EVO DSP TM 35 User’s manual Static Bypass Number of phases 1 Phase + Neutral Voltage range (Line-Neutral) [V] *(Note 1) 220 / 230 / 240 ± 10
User’s manual 36 UPS EVO DSP TM 12 Internal Battery Location - Connection Instructions 1) Take out all the drawers outside of the UPS. 2) Place
UPS EVO DSP TM 37 User’s manual 13 Internal Battery Location - Connection Diagram Internal Battery Location is available at the UPSs from 10kVA t
User’s manual 2 UPS EVO DSP TM Index 1 Safety ...
User’s manual 38 UPS EVO DSP TM
TECNOWARE S.r.l. www.tecnoware.com
UPS EVO DSP TM 3 User’s manual 8 Communication Interfaces ... 28 8.1
User’s manual 4 UPS EVO DSP TM 1 Safety Information related to the safety of the UPS, loads and the user is summarized below. But the equipment s
UPS EVO DSP TM 5 User’s manual 2 Installation 2.1 Transportation The UPS must remain in a vertical position throughout the transportation. Make su
User’s manual 6 UPS EVO DSP TM Access is through the use of a tool or lock and key, or other means of security and is controlled by the authorize
UPS EVO DSP TM 7 User’s manual According to EN 62040-1-2, the user shall place a warning label on the input distribution panel and the other prima
Kommentare zu diesen Handbüchern